Home»Accessories»Spring Truck»MINI Hangers with Spacers & Nuts »ULTIMATE Hanger MINI - TITANIUM WHITE

The ULTIMATE TITANIUM HANGER is a slimmed down SUPER light weight version of the original INFINTY Hanger. The Hanger body is produced from CAST ALUMINUM and is one solid piece. Without stripping any of its critical strength a CNC milling machine accurately cuts out the bulk of the material which results in the ULTIMATE hanger being almost as strong as the Infinity BUT nearly 30% lighter in over all weight. :-)

The ULTIMATE Hanger is then drilled & fitted with SOLID 9.525mm TITANIUM Axles. The TITANIUM Axles reduce the overal weight of the ULTIMATE hanger even further. Marine Grade Stainless steel GRUB SCREWS help keep the TITANIUM Axles locked into the correct place within the Hanger.

The CNC milling guarantees to drill accurately. Ensuring the Kingpin Holes are accurately placed guarantees' the best performance to the rider as well as making the truck easy to assembly & service. In order to give the "Two Tone Pimp Finish" the Ultimate Hanger is POWDER COATED Gloss White for metal protection & colour coordinating good looks before the CNC work is carried out.

The Ultimate hanger measures 16 Inches in total width. When the wheels are fitted to the Hanger, the board has a center wheel width of 14 Inches.

TRAMPA's ULTIMATE Hanger uses 2x 18.2mm x 9.525mm SPACERS (1 either side). The spacer slips onto the axles, leaving the perfect space to mount the TRAMPA wheels accurately. Use the 3/8/ths of an inch Axle Nuts to lock the wheels into place on the axle.

Kingpin bushings push into the Kingpin holes, in both the Hanger & the Baseplate. When all the bushings are in position, push the Baseplate over the Hanger and into position so that all the Kingpin holes line up. When this is the case you will be able to push the kingpin, from the front to the truck to the back, through the holes in the assembly & connecting them all together. Remember to add the washer onto the kingpin before sliding into the assembly. As these bushings are made from plastic and sit in between moving metal parts, these small parts (bushings) will need checking & possibly need replacing over time. So its good practice to check & replace them when you swap your hanger or make service work to your trucks...

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

PRECISION Shim spacer - STAINLESS STEEL - Bridges tiny gaps on axles - 9.525 x 13.525 x 1mm

This tiny STEEL Shim Spacer is precision made to give maximum performance! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the axle fitting either side of the Bearings when the wheel is being fitted onto 9.525mm Axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good proactice will ensure your board stays in tip-top condition, always!

Mini ULTIMATE Hanger - 9.525mm TITANIUM Axles, Powder Coated White & CNC'd light

The Mini ULTIMATE Hanger measures 12.5 Inches in total width & it fits to all TRAMPA Spring Truck Baseplates. Being narrower in the body & fitted with shorter axles than regular ATB Hangers means the overall steering characteristics are completely different. The ULTIMATE Hanger has the usual Spring Adjuster facility but is also drilled with 2 spring mounting positions & by changing the spring positions in the truck (inside or outside position) or by adding/removing some TRAMPA DAMPA's into/from the springs means the Mini ULTIMATE Hanger has an incredibly broad range of controllable steering which can be used for so many different applications its simply ace!

The Hanger body is made from FORGED ALUMINUM & comes as one solid piece. Its fitted with 9.525mm (10mm) TITANIUM Axles. TITANIUM Axles are half the weight of steel Axles but when compared "weight for weight" the Titanium is much stronger! The Mini ULTIMATE Hanger is a slimmed down light weight version of the Mini INFINITY. We use the CNC machine to accurately drill the Kingpin Holes & to cut out the bulk of the material to save weight, whilst still retaining the majority of its solid strength. CNC work is expensive but seriously reduces weight. :-) Ensuring the Kingpin Holes are accurately placed guarantee's best performance to the rider as well as making the Truck easy to assembly & service. The Mini ULTIMATE Hanger is Powder Coated WHITE for metal protection & colour coordinating good looks before CNC work is carried out.

Mini Ultimate Truck Hangers are used in BOTH the ULTIMATE TREET Carver Trucks & the amazing ULTIMATE URBAN Carver Trucks. The only difference between the Street & Urban Carver Trucks is the facing direction of the hanger. By turning the hanger around during assembly allow's the different style of Truck...  Axle facing forwards for Urban, Axle facing backwards for Street.

We turn the Hanger around because the axle position is not centrally located in the Hanger and so by facing the axle forwards away from the toe's, extends the wheel base whilst at the same time lowers the ride height of the deck (You have to remember the truck is mounted to the deck at a 35º), making the resulting Truck & Deck combination wheel base much more suitable for mounting a larger wheel, HENCE why the URBAN CARVER Truck uses the 7 inch pneumatic wheels.

Equally, Where as when the hanger is reversed & the Axle is facing towards the riders toe's, the wheel base is shortened & of course the deck height is subsequently raised slightly, co-incidentally to a perfect height to fit much smaller style of wheel & you guessed hence why the Street Carver Deck uses the 83mm or 90mm Longboard wheels.... :-)