VESC 6 MkVI - 12s

Introducing the amazing VESC® 6 MKVI Speed Controller, the 6th major product update of the world famous VESC 6 motor controller product line. Packed with a variety of amazing new features, this VESC motor controller is certainly worthy of it’s pimpin’ gold logo.

New features, setting it aprt from the previous MKV edition are: Second UART port, increased current handling, SPI wired IMU, sensor voltage adjustment in software, Spin-To-Sart deactivation option, black anodized housing.

The first VESC controller capable of hibernating, your board can conserve power while not in use - reducing power consumption to just 20μA – less than the self-discharge rate of the batteries. Or with automatic power off, your VESC controller can switch itself off after a set amount of time.

No more loop keys! Compatible with power buttons / switches, the VESC 6 MKVI controller can be ready to go with a single press / flick. If desired, multiple devices can share a single button.

STS (Spin-To-Start) – it’s possible to set your board to power up with a small kick/nudge! This feature can now be enabled or disabled.

In its development, no Mosfet switches were used - due to their tendency to eventually blow up. This saves on the additional costs of replacing them, & also adds to the longevity of the VESC 6 MKV.

When we developed the VESC 75/300 controller, it was obvious that most of its features would be handy to have in the VESC 6 controller format.  As a result, Benjamin Vedder took on the challenge and re-designed the entire PCB of the VESC 6 controller, to make new, powerful features available in a smaller & cheaper 60V rated package.

The VESC 6 MKVI controller features THREE PHASE SHUNTS & adjustable CURRENT / VOLTAGE FILTERS - detecting any motor attached more precisely and reliably than ever before. Consequently all kinds of motors now run as smooth as butter & react PERFECTLY LINEAR to throttle input commands.

For salient motors the VESC 6 is also cpable of sensorless full torque from zero RPM, silent HFI and sensorless position control with the accuracy of a high precission encoder.

You’ll also find a new SPI wired IMU chip fitted - featuring a 9 axis gyroscope, and accelerometer, the VESC 6 MKVI knows its 3D orientation in space, and 3 axis acceleration values.

UAVCAN has been added to the firmware allowing to interact with commonly used flight controllers like the PIXHAWK ®* devices. An incredible 12,000 lines of code have been added for the new hardware releases. To make the VESC controller nearly indestructible, the low voltage rails were redesigned A-Z.

VESC-Tool software is now available as an Android™ and Apple compatible App, allowing you to configure your VESC or VESC controller array with only a few clicks. User specific PROFILES will let you change in between different setups with a single tap on the fly.

Using an original VESC 6 MKVI controller, motor detection is now more precise than ever. Extreme low inductance (0.5 μH) motors are no issue! 

Parameters for gearing and wheel diameter have been added, allowing display of speed, Wh usage per distance travelled, precise battery indicator, current consumption, duty cycle and power. Beautiful self-adjusting analogue displays make the readings of all parameters very enjoyable.

What makes the original VESC hardware so special?

The original hardware is perfectly matched to work seamless withe VESC-Tool software code. Both, hardware and software, have been designed by the same engineer, knowing all critical detail.

TRAMPA BOARDS LTD has teamed up with the internationally renowned 'YODA of electronics' (Benjamin Vedder) to bring to the world the most advance electronic speed controllers ever to be produced! Benjamin's family name is Vedder & the V in the brand VESC represents this. VEDDERs Electronic Speed Controller! There have been many ESC's before, but now the VESC line of products officially exists, made to work seamless with the latest software developments. Benjamin is globally renowned for his incredible electronics and software skills. He has worked tirelessly for well over 9 years fine tuning preceding versions of the globally famous & now Trade Marked VESC products & after teaming up with TRAMPA BOARDS Ltd the development of the VESC product line has taken him to his highest capability yet.

The TRAMPA VESC controllers  comes fitted as standard with TRAMPA's very own & very special Silicone Coated & TRAMPA logo'd cables which are made up of 1036 Strands of Highly Flexible Top quality German copper. These quality details ensure the maximum performance at all times. Attached To the premium copper cables are genuine Amass XT90s connectors one side & 4mm Gold Plated Bullet connectors the other. The VESC 6 MKVI is installed with a custom moulded Internal Silicone Seal & is neatly fitted into the Heat sink which is a Solid Block of CNC'd  6061T6  Aluminum, used for dispensing the heat and offering maximum protection, allowing easy fitting and maximum good looks!..

The VESC line of produces are the most powerful & impressive Electric Speed Controller Benjamin has ever envisioned! They are  arguably by far the best and most versatile Electronic Speed Controllers the world has ever seen!! E Boarding, E-Biking, Remote control of all kinds including Drones & Robotics and Camera equipment (as well as thousands of industrial & recreational applications) are all about to be revolutionized by using the VESC series of products that will all come to the market soon...

Using the a VESC controller in your TRAMPA BOARD setup (Regardless of which model) will allow you to add any battery up to 12s with 60V of peak voltage. This is the perfect limit to give you incredible performance from your electric TRAMPA motors or similar. Using the new VESC TOOL software, you will be able to fine tune your performances relevant to your application, where you will be able to calculate your top end speeds & approx distance to travel using different combinations of power & gearing settings. Beautiful!

VESC controllers comes to you ready to plug in & go! They are delivered to you in a very stylish precision cut 6061 T6 aluminum heat-sink housing which has the TRAMPA & VESC logo beautifully laser etched to its surface & for further splash proofing we have invested into another mould for additional exterior Silicone Sealing which is available as an accessory to purchase.

The performance of the TRAMPA VESC controllers, compared to preceding third party models, is light years ahead! This is demonstrated in the cost as cheap non effective clones are sold according to their price not their quality. If you want the best performance then stick to the original hardware source - it will save you a lot of money on the long run and is a guarantee for ultimate performance and max compatibility with future software releases.

Our VESC controllers are being configured with the brand new Open Source, GPL V3 licensed VESC®-Tool Software:  www.vesc-project.com and on the Google Play Store™*.
The Open source, GPL V3 licensed VESC Firmware will come pre-installed on the device, allowing us to do extra testing of the device, prior to shipping.
This is the GPL V3 license contract for your reference:  www.vesc-project.com/GPL V3

Features

- Current and voltage measurement on all phases (three phase shunts)
- Adjustable current and voltage filters (full phase filters)
- built in, SPI wired  IMU chip (accelerometer, gyro)
- Spin-To-Start
- Auto power off timer, adjustable - Regenerative braking
- Traction control (single and twin setup)
- Sensored or sensor less operation + hybrid mode
- full torque from zero RPM
- sensor less position control for most salient motors
- Configurable RPM-, current-, voltage- and power limits
- Input source: CAN, PPM, Analog, NRF
- Communication ports: USB, CAN,UAVCAN,  2x UART, SPI, I²C
- Throttle curve and ramping for all input sources
- Separate throttle curves for acceleration and brakes
- Seamless 4-quadrant operation
- Motor revolution, amp hour, watt hour counting
- Display of speed, power, duty cycle, amp flow, estimated range and battery status on App
- Accumulated data from arrays of VESC controllers
- Real time data analysis and read out via communication ports
- Real time data analysis and read out via VESC-Tool APP or VESC-Tool software
- Adjustable protection against:

          -    Low input voltage
          -    High input voltage
          -    High motor current
          -    High input current
          -    High regenerative braking current (separate limits for the motor and the input)
          -    High RPM (separate limits for each direction).
          -    Over temperature (MOSFET and motor)

Technical Data Sheet

- Voltage: 11.1V – 60V (Safe for 3S to 12S LiPo).
- Voltage spikes may not exceed 60V, do not use 13S LiIon!
- Current: Continuous 80A, peak 120A.  Values depend on the temperature and air circulation around the device!
- 5V 1A output for external electronics
- 3.3V 0,5A output for external electronics
- Modes: DC, BLDC, FOC (sinusoidal)
- Supported sensors: ABI, HALL, AS5047 and other encoders

* Android is a trademark of Google LLC.
Google and Play Store are trademarks of Google LLC.
PIXHAWK is a trademark of Lorenz Meier

In CNC T6 Silicone Sealed Aluminium Box with Genuine XT90 Connectors - Vedder Electronic Speed Controller TRAMPA Special