Home»Trucks»14FiFties - 14.5 Inch Wide Longboard Trucks »14FiFties Extra Wide All Terrain Longboard Truck - 12mm Axles

TRAMPA's Super Sexy 14FIFTIES 'Supa-Dupa' Extra Wide Longboard Trucks are absolutely fabulous! CNC precision shaped from a solid Block of T6 Aluminum, the 50º Mounted Hanger measures 14.5 Inch wide & is fitted with 12mm (7/8ths of an inch) Hardened  & Hollowed Steel axels which means the EXTRA WIDE Longboard Truck will accommodate every wheel in the TRAMPA product range from 125mm GUMMIES Longboard Tyres, the Amazing 6.5 Inch URBAN TREADS Tyres, 7, 8 & Even enough spae on the hanger to fit 9 Inch Wheels!!!

Being 14 Inch's wide & Mounted at 50º the 14Fifities 'Supa-Dupa' Extra Wide Longboard trucks are named after around dimensions. The 'Supa-Dupa' Extra Wide Longboard Trucks provide high speed stability & the ability to be able to use Pneumatic tyres, which beings a complete new ride experience when riding the rough roads that surround us, cruising over cracks in the pavement becomes glorious!

3/8ths Nut - Marine Grade Stainless steel Nylock HALF nut W3/8 - 24T UNF

This very special Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore reducing weight in the Truck also! A few Grams here & a few grams there soon adds up to quite alot & that makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area...

This very special 3/8^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W3/8_^ths - 24T - UNF. This Nut is used to hold the wheels onto the axles of the 9.525mm (3/8ths of Inch or otherwise referred to as 10mm) SKATE TRUCKS & also the Spring Trucks fitted with TITANIUM axles. This Nut is also used to hold the KINGPIN in position on all Skate Trucks. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 14mm or 9/16^ths of an Inch spanner to tighten the Nut onto the Axle or Kingpin, do not overtighten the nut, allow the wheel to spin freely but not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

 - Fits to 9.525mm (3/8ths) Axles & Skate Truck Kingpins

7/16ths Nut - Marine Grade Stainless steel Nylock Axle HALF nut (W7/16-20T UNF) - Fits to 12mm Axles

This very special 7/16_^ths of an inch Marine Grade Stainless steel Nyloc HALF NUT is custom made specially to fit the TRAMPA products. Half nut means - half as the size of a regular nut, so half the size = half the weight of a normal nut.. By using Half nuts on the axles reduces the over all length of the axle & kingpin therefore further reducing weight in the Truck! A few Grams here & a few grams there soon adds up & makes all the difference to the total Truck & consequently deck weight, specially in critical areas of the deck such as the wheels area, where a few grams makes all the difference...

This very special 3/8_^ths of an inch Marine Grade Stainless steel Nylock Half Nut official factory measurements are  W7/16 - 20T - UNF. This Nut is used to hold the wheels onto the axles of the Spring Trucks fitted with 12mm axles. The Nut is fitted as standard with the world renowned NYLOC System. The Nyloc "locks the Nut onto the Bolt" eliminating vibration, keeping your nuts tighter for longer!

Use a 16mm or 5/8th_^ths of an Inch spanner to tighten / loosen the Nut onto the Axle or Kingpin. Do not overtighten the nut & make sure the wheel can spin freely but does not rattle & do not crush your bearings. Being Marine Grade Stainless Steel this nut will not rust you! Always ensure all ur nuts are tight before you ride!

Wheel support spacer for all TRAMPA Wheels on 12mm ATB Axles - CNC precision 12mm x 16mm x 18.2mm - CUSTOM

This special Spacer measures 12mm (id) x 16mm (od) x 18.2mm (long) & has 2 uses!. It is firstly known as the Bearing Support Spacer as this Spacer fits between the Bearings of a 6 Spoked HYPA Hub, (when mounting the HYPA wheel onto 12mm Axles) & secondly it is also known as the AXLE SUPPORT SPACER as this spacer is also used to position any of the TRAMPA wheels in the perfect position onto the axles of 12mm TRAMPA Spring trucks....

TRAMPA spacers are produced as one long tube. The Tube is Heat Treated to gain extra strength & is then Bead Polished to give the metal extra surface protection & a shiny best appearance. The tube is then cut to the exact length for precision mounting. 

PRECISION Shim spacer - Bridges the tiny gaps between bearings on 12mm axles - 12 x 16 x 1mm

This little STAINLESS STEEL Shim Spacer is precision made. It ensures maximum performance to the wheels & nuts. Made from Marine grade stainless steel it will not rust on you! It is used to hold the bearings in the perfect position & also to bridge tiny gaps on the axles, ensuring an accurate fit with NO rattles!

The Shim spacer slips onto the Axle, fitting either side of the Bearings when the wheel is being fitted onto 12mm axles.

This tiny spacer positions the wheel perfectly on the axle, holding the Bearing in the best possible place to help achieve maximum spin rate for the bearing & wheel. Its little parts like these that suffer the most amount of abuse, especially when they are used in the harsh conditions that they are. Check from time to time they are in good order & possibly replacing them every now & then this good practice will ensure your board stays in tip-top condition, always!

14FiFties Extra Wide Longboard Hanger 355mm with 12mm HOLLOW Steel Axles

Introducing the 14-FiFties EXTRA EXTRA Wide Longboard HANGER, the newest edition to TRAMPA's range of amazing Long-Board Parts. 

Almost identical in design to TRAMPA's amazing 12-FiFties Trucks, TRAMPA has beefed up the 14FiFties & feeding them on steroids, having added some extra bulk to the body & fitted them with 12mm Axles to accept larger wheels....

The 14-FiFties Trucks have been specially made to celebrate TRAMPA's 20th Birthday (02.02.2022) & to fit TRAMPA's very latest ORRSOM GT Longboard Deck that's due out in early 2022....

So you know the terminology & how it is the 14-FiFties got its name, the 14FiFties Hanger with 12mm Axles mounted, measures 14 inches wide, whilst the mounting angle of the Kingpin is 50 Degree's, so the name 14FiFties was easy spawned...

Designed to be used in conjunction with our NEW ORRSOM GT longboard deck , the 14FiFties Trucks  use the same parts for assembly as or 12FiFties Hangers , BUT NOW with Customizable Baseplate colors & Endless Bushing options.

The extra 2 inches width provides superior stability, specially at high speed, as well as the extra clearance needed for adding larger wheels (Adding larger than 6 inch wheels to the 12FiFties Trucks would often result in toe bite on tight turns). The 14FiFties Trucks being fitted with 12mm Axles are compatible to house wheel sizes from 6.5'' (URBAN Treads - for speed street cruising), all the way through the range up to 9'' pneumatic tires - providing the most unrivaled off road Long- Board Style Board experience ever.

TRAMPA's 14FiFties Longboard Trucks  are the widest, strongest, longest, electric longboard trucks on the market today!

Designed to fit with our standard sized Skate Truck kingpin (9.4 x 50mm) & mounted at 50º angle to the base plate for optimal steering responsiveness. 

14FiFties  Base plates are available in 10 different anodized colors for unrivaled customization! 

Precision CNC'd from solid blocks of T6 heat-treated Aluminum, 14FiFties HANGERS are remarkably strong, able to withstand the forces, bumps or crashes they'll inevitably receive if ridden properly. As well as looking the part with an andonised black finish!

The hanger body has been CNC'd and then where crucial for motor mounting milled down to 19.5mm x 19.5mm. Since this is a 'one of a kind' longboard truck, it would have not been complete without its very own electric motor mounting system, based on the All-terrain Open Belt Drive system developed for the MTB spring trucks offers unrivaled performance (customized with a range of wheel and motor pulley options), straight forward installation and trouble-free maintenance. 

Custom Blood Orange Bushings - High Performance Urethane Bushings with lots of Flex options for customisation

The TRAMPA-IR truck and 12/14FIFTIES longboard trucks make use of Blood Orange's Barrel, Insert and Wedge bushings.

Using a high responsive nylon formula, the barrel bushings are designed to eliminate any gaps between bushing, hangar and kingpin. Less play on the pivot axis means improved responsiveness and a rapid return to center for those ultra tight turns!

The barrel design has been refined over many years through the development of skate truck design, and has proven to be strong and rugged.  The high rebound properties of the urethane also means it doesnt loose its uniform leaning properties, which is essential for downhill stability. 

Rubber hardness is measured in Shore Durometer resistance, These Skate Bushings are 89a rubber hardness, an ideal for greater stability at high speed, while reducing some turning capability. Used in conjunction with a flat plate washer, the bushing can be tightened onto the kingpin to increase steering resistance.

Custom Blood Orange PLUG BARREL Bushing - High Performance Urethane Bushings with lots of Flex options for customisation

The TRAMPA-IR Truck & 12/14FiFties longboard Trucks make use of Blood Orange's PLUG Barrel & WEDGE bushings.

Using a high responsive nylon formula, the insert bushings are designed to eliminate any gaps between bushing, hangar and kingpin. Less play on the pivot axis means improved responsiveness and a rapid return to center for those ultra tight turns!

The unique stepped plug design sits within the bushing recess on the IR hanger which helps the complete truck become more stable and restricts unwanted movement within the double kingpin design making it very comfortable at high speeds.

Rubber hardness is measured in Shore Durometer resistance, These Skate Bushings are 89a rubber hardness, which are and intermediate hardness giving good compromise between stability at speed and responsiveness when carving. Used in conjunction with a flat plate washer, the bushing can be tightened onto the kingpin to increase steering resistance.