£0 
This site is best viewed in Google Chrome, Firefox or Safari. Click here to remove this message.
REAR Fender Kit for 9 Inch Wheel boards - PRO BELT DRIVE
-
8x M4 x 16mm TORX Countersunk bolt Marine Grade Stainless Steel -
4x M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel -
8x M4 Washer Marine Grade Stainless steel -
4x 8 inch Mud Guard T6 Mounting Spacer V2 - PRO BELT DRIVE 4.1 ID x 7.5 OD x 7.5 L -
2x 9 inch Mud Guard T6 FENDER Mounting Bracket -
2x 9 Inch Wheel Mudguard Fender -
1x 9 inch Mud Guard 3mm Carbon Fibre PRO BELT DRIVE Mounting Panel - RIGHT -
1x 9 inch Mud Guard 3mm Carbon Fibre PRO BELT DRIVE Mounting Panel - LEFT
M4 x 16mm TORX Countersunk bolt Marine Grade Stainless Steel
TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush.
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel
TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush.
Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!
Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.
There is nothing worse (or better) than blasting through a muddy puddle only to be complete covered in the spray that obviously flies of all 4 wheels when out riding on a Electric Mountainboard, its possible to get yourself & the expensive electronic equipment completely covered in XXXX in just one moments riding, which not only leaves you worried that all the electronics will be ok, but also means you have some serious cleaning to do when you get home! lol And that's why we made these Mud-Guards & TRAMPA's Mud-Guards aka 'XXXX-Shields' work wonders!!
Using CNC T6 Aluminum Hanger Mounts attached to Carbon Fiber Mounting panels (all the usual high quality touches TRAMPA add's as standard to most of its builds) the mudguards give enough cover to prevent you and your equipment from getting plastered in muck when out riding in the worst of conditions....
There are different Mud-Guard mounting Clamps to work on both the original and the new CNC TRAMPA Hangers which will mount to the front of the Board, But the REAR Mud-Guards are only designed too fit to the Pro Motor Mounts, & the different Pro motor mounts have a different fitting kit, so if you wish to make a purchase please make sure you get the correct kits you need for the Trucks you have at the front and the Motor mounts you have at the rear. If you get stuck or not sure which trucks or mounts you have, drop the guys a line for advise as to what you have & they can tell you what you need....
This Mudguard kit is designed to work with the CNC PRO Mountainboard Hanger fitting 2x mudguards to the REAR of the deck for a PRO BELT DRIVE Motor Mount. 1 kit covers 2 wheels at the rear.
2x 9 Inch Wheel Mudguard Fender
1x 9 inch Mud Guard 3mm Carbon Fibre PRO BELT DRIVE Mounting Panel - RIGHT
1x 9 inch Mud Guard 3mm Carbon Fibre PRO BELT DRIVE Mounting Panel - LEFT
4x 8 inch Mud Guard T6 Mounting Spacer V2 - PRO BELT DRIVE 4.1 ID x 7.5 OD x 7.5 L
8x M4 x 16 Countersunk TORX bolt
4x M4 x 35 Countersunk TORX Bolt
8x M4 Washer Form B - Marine Grade Stainless Steel
Weight: 376g
HCC: 8714929000
Related Products
+44 (0)115 8410006
All images and material on this site not covered by other copyright and not explicitly marked as public domain is © Trampa Boards 2000 - 2024