Home»ELECTRIC COMPONENTS»Battery Boxes»BEAST Box - 6.2Ah Li-Po»MkIII 6.2Ah BEAST Box fits 2x 6s 6200 mAh cells

DESCRIPTION

TRAMPA's amazing 12s battery box will change your life! It will fit to any of the TRAMPA boards with Spring Trucks! It is made from 2mm thick 3k Twill Carbon Fiber & has been precision CNC machined as well as being internally grooved to give perfectly tight connections, especially the corners, making the Beast Box pretty much Water proof... For sure, heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

TRAMPA's amazing 12s Beast Box will snugly fit 2 x 6s Zippy compact batteries (other other similar size batteries), which when harnessed together makes 12s beast!! The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!! (for a guide to set this up for your batteries click here)  12s Power is heaps & a Single TRAMPA Motor 12s Deck is more than plenty powerful enough for most riders. TWIN motor decks do not make you go faster at top speed, but TWIN Motor Decks do make you accelerate considerably faster & TWIN Motor deks will give you a lot more grip especially when riding off road in loose dirt. Its really worth consider purchasing TWIN motors if you are either a regular steep hill climber where two motors share the load of 2 motor, or if you intend to be riding off road alot where you will benefit so much more from the extra traction & grip that is gained, or if you just want the most awesome looking best bit of kit with the maximum performance you can get...!

2x 6s batteries loop together to make 1x 12s Battery. This can then be split using a XT90 cable splitter to power into TWO VESC's providing TWIN Motor power! You will need 1x V6 VESC speed controller for each motor. The single V6 VESC connects neatly inside the beast box making it very easy to neatly connect the wires up for the non experienced Electric Board'r. or externally connect to TWIN V6 VESC for Twin Motor Power! 

Assemblying the box is fidlly but fun! lol! Stainless steel Countersunk bolts harmoniusly connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you get a sastisfying click of confidence that everything has dropped into place perfectly as the panels slips into the groove and the gaps are no longer visable! Awesome bit of kit!

When installing your chosen batteries into your BEAST BOX, it’s a good idea to secure them to the inside with velcro, then pad the area around the batteries with foam. This reduces any ride-ruining-rattling sounds & keeps the batteries safe from bouncing around when riding over rough terrain.Battery Box Width - 110m

Battery Box Length - 200mm
Everything fits Internally with single V6 VESC
TWIN V6 VESC Fits externally with new Waterproof Silicon Seals

MkIII BEAST Box Carbon Fibre Panel kit with integrated LED & NRF Housing - Fits 2x 6200 Zippy compact

TRAMPA’s Beast Boxes come in three different sizes;

STANDARD - fitting up to 6200mAH Batteries

BIGGER - fitting up to 12,000mAH Batteries

BIGGEST - fitting up to 16,000mAH Batteries.

Boards with single motors could go for any of the Beast Boxes - dependant on the desired range / weight of the finished board.

Boards with TWIN Motors will need to go for the BIGGEST BOX, in order to accommodate room for the extra VESC that needs to sit inside.

Able to fit onto any TRAMPA board with Spring Trucks, BEAST BOXES made from 2mm thick 3k Twill Carbon Fiber & are precision CNC machined & internally grooved to give perfectly fitted joins, making the Beast Box pretty much water proof. Heat shrinking your joins & adding a touch of silicon at the end of the assembly will for sure seal the box to be tight from water!

The beast box comes with a top mounted LCD Battery Indicator, so guessing range is no longer an issue!

Assembling the box has been described as “fiddly but fun”. It’s a tight fit when using the biggest batteries for each box, so keep that in mind while assembling. The less room the batteries have to bounce around inside the box the better - especially over rougher terrain!

Stainless steel Countersunk bolts harmoniously connect into both the base & the lid of the box, screwing neatly & tightly into HEX spacers... as the lid is tightened down, you'll get a satisfying click of confidence that everything has dropped into place perfectly, as the panels slips into the groove and the gaps are no longer visible!

Battery Box Width - 110m
Battery Box Length - 200mm
Averything fits Internally!

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

M6 x 30mm Countersunk Allen-Key Bolt - Marine Grade Stainless steel with locking paste

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

The head of this Bolt is COUNTERSUNK, meaning that when screwed into position it sits flush & neat with the surface its screwed into. Preventing bolts from standing proud eliminates the chance of anything getting "snagged or hung-up" should it get caught on something..

Used For;

- 6-8s Battery Box

- 8-10s Battery Box

-Beast Boxes

M4 x 10mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 35mm TORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 25mmTORX Countersunk Bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 50mm Aluminium Threaded Spacer Nut Used for assemblying the Battery Boxes

Used for assembling the MONSTER BATTERY BOX.

x9 Required per box