Home»Accessories»Bolt Kits »Monster Box Assembly Kits»Massive Monster Box Assembly Kit

Cable Harness for wiring Power Switches to VESCs

Harness allows connection between VESC 6 MkIII or newer and on/off switch.

TRAMPA Switch with 5V LED QUALA-T logo & 16mm Stainless Steel Fixing Nut

The TRAMPA 'QUALA-T" stamped Power Switch is a sexy little switch & to co-ordinate with the huge array of anodised & painted colours that TRAMPA offers to tie into all the other kit we offer is available in 6 different colours - RED, BLUE, YELLOW, GREEN, WHITE, PINKY/PURPLE

Which means no more loop keys!
All TRAMPA Mountainoboards Boards fitted with VESC 6 MKIII & any later models can now be fitted with power buttons for easy powering on/off and a much sleeker looking board!

You will need a Power Switch Cable harnesses to plug in

The QUALA-T Switch is Non-latching & limited to a Max voltage of 5v 

5mm Cable Entry OPEN Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes

5mm Cable Entry Open Rubber Grommet - Allows TRAMPA Silicone Cables to pass through sealed holes in Monster Box side panels for water proof assistance & Neat Cabling

OVAL Rubber BLIND Grommet Cable Entry Hole - Fits in Monster Box side panels for water proof assistance & Neat Cabeling

This OVAL Rubber BLIND Grommet Cable Entry Blank is used to seal of Entry Holes in MONSTER Box, BEAST Box & Underboard Battery Tray which fits on the ORRSOM longboard. Simply push the Oval Grommet into position & your entery holes is sealed from moisture & dust.

If you need to push a cable through, use a sharp knife and carefully slice through the rubber membrane.

5mm ROUND BLIND Rubber Grommet for 5mm TRAMPA Silicone Cable

This 5mm Round Blind Grommet is used to seal off un used Motor Cable Entry Holes in the MONSTER Box, BEAST Box & Underboard BATTERY Box.

The 5mm Round Blind Grommet should also be fitted into all Battery Boxes which are using the Motor Cable entry holes as passing the cables through the 'OPEN' Grommet seals the hole best as possible & protects from the ingress of moisture & dust. 

To open the grommet to pass a cable through simply use a sharp Knife to press against the pre pressed slicing line & slice open the Rubber Membrane to allow you to push your cables through. Easy!

M4 x 16mm TORX Countersunk bolt Marine Grade Stainless Steel

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 10mm TORX Dome/Button Headed Head Bolt Marine Grade Stainless Steel TORX

TORX Screws are less likely to strip out when compared to a hex screw, because of the way the load is distributed and applied between the tool and the hardware. Because of this load distribution, the height of the head of the bolt can be reduced - making them nice & flush. 

Made from A4 Marine Grade Stainless Steel, all of the nuts, bolts & screws used in a TRAMPA board have proven to be up to the challenge of holding everything together. Using Marine Grade Stainless Steel also means these Bolts will never rust on you! They can cope with the harshest of weather conditions & will laugh in the face of sandy/salty beaches or muddy freeride tracks - which can turn other manufacturers’ nuts & bolts into corroded rusting wrecks!

Wherever possible, we dip all our bolts into BLUE THREAD LOCKING PASTE, to ensure an extra strong & secure fix between the nuts & bolts.

M4 x 80mm Aluminium Threaded Spacer Nut Used for assembling the BEAST Battery Boxes

Used for assembling the BEAST BATTERY BOX.

x7 Required per box

M4 COUNTERSUNK Washer Anodised

M4 Countersink Washer great way to pimp and customise your board in 10 differnt colours used in conjunction with all our M4 Countersunk bolts great way to finish off your board/project